Older Genuine Aloris Cxa Quick Change Tool Post Turret For Metal Lathe

USED, WORKING ALORIS CXA TURRET. I TRIED IT OUT WITH SOME CXA HOLDERS AND IT HOLDS AND LOCKS DOWN LIKE IT SHOULD. THERE ARE MEASUREMENTS IN THE PICTURES. THE TURRET HAS SCUFFS AND SCRATCHES FROM USE. NO HOLDERS, TOOLING OR ANYTHING ELSE INCLUDED. IF YOU WIN MULTIPLE LISTINGS WAIT FOR ME TO SEND AN INVOICE. […]

Post Tagged with , , , , , , , , ,
Read More

40-Position Quick Change Tooling System (Toolpost, Multifix-type)

Although the ad from Rutland says the toolpost is for 10-15 inch lathes, it was obviously too small for my 14-inch as the previous owner had installed a riser plate underneath it. I would recommend that this equipment be used on lathes 12-inches and smaller similar to an Aloris AXA. One(1) 40-position toolpost w/tightening wrench. […]

Read More

Quick Change Tool Post for Unimat Lathe DB200 /SL1000

Quick Change Tool Post Sets for Unimat DB200 and SL1000. Tired of shimming your tool bit to get the right height for your tool bits? Long set up time to switch from one tool bit to another? QCTP was designed specifically for Unimat DB200/SL1000 lathe. The set comes with five tool holders to hold 1/4″ […]

Post Tagged with , , , , , , ,
Read More

Quick Change Tool Holder Set Yuasa R8 for Bridgeport set 2

Quick Change Tool Holder Set Yuasa R8 for Bridgeport. Condition is very good Used. Comes with 3/16, 1/4, 3/8, and 1/2 Tool holders and a J6 arbor for a Drill Chuck. Please check the pics out for the real condition. I have 4 sets of these that I will be listing. The item “Quick Change […]

Post Tagged with , , , , ,
Read More

40 Position Quick Change Tool Post Kit Multifix QCTP Size B2/B with BD25120

Ed on lathes which turning diameter is from 300mm to 500mm. C06236, MATE360, C6240, Yangzhou Super C6241, C6246, etc. To select a right tool post for your lathe, swing over bed is not the only data to refer. Also need to know your lathe tool top slide width and lathe main motor power. For a […]

Post Tagged with , , , , , , , ,
Read More

Genuine Aloris CXA Quick Change Lathe Tool Post Holder with 5 holders

Genuine Aloris CXA Quick Change Lathe Tool Post Holder with 5 holders. Used condition, works good. Comes with two DTM H90-2A, CXA1, CXA13 and a CXA4 holders. Take a look at my other auctions to see if there is anything other machinist tools that you might be interested in. The item “Genuine Aloris CXA Quick […]

Post Tagged with , , , , , , , ,
Read More

R8 Quick Change Tool Holder Set Bridgeport Brand

Quick Change Tool Holder Set for R8 spindle milling machines. Bridgeport brand all pieces. Condition is very good Used. Comes with Tool holders and a J3 arbor for a Drill Chuck along with the shell mill holder arbor. A little scotch bright and these will clean up good. No pitting just surface dirt. Please check […]

Post Tagged with , , , , ,
Read More

AXA Piston Quick Change Tool Post and Tool Holder for Lathe 6-12 250-100 Set

AXA Piston Quick Change Tool Post and Tool Holder for Lathe 6-12 250-100 Set. Suitable for lathe center height 0.6 – 1.75 (top compound surface to lathe center line). It is precision engineered to assure repetitive accuracy. No time wasted with shims. All working parts hardened and precision ground. The tool post comes with a […]

Post Tagged with , , , , , , , ,
Read More

Quick Change Tool Post 3

Post Tagged with , , ,
Read More

New AXA Size 250-111 Set Wedge Type Quick Change Tool Post Set for 6-12 Lathe

New AXA Size 250-111 Set Wedge Type Quick Change Tool Post Set for 6-12 Lathe. 250-111 Wedge Type Tool Post. 250-101 Turning Tool Holder , use tool bit up to 1/2. 250-102 Boring, Turning Tool Holder, use tool bit up to 1/2″ and round shank tool bits up to 7/16″. 250-104 Heavy Duty Boring Bar […]

Post Tagged with , , , , , , , , ,
Read More

Swiftray Theme Powered by WordPress