Blog Archives

Quick Change Tool Holder with R8 Collet Shank Set Lot

Quick Change Tool Holder with R8 Collet Shank Set Lot.

Post Tagged with , , , , ,
Read More

BXA 250-222 Wedge Type Quick Change Tool Post Holder 6Pcs Set Swing Dia 10 15

Suitable for lathe center height 0.7 – 2.2″ (Top compound surface to lathe center line), such as: South Bend 13″, 14″ & 1307, Delta 14″, Logan 14″ Emco: Elnomat13S, Harrison: 11,12 &13″, Sheldon: 11 &13, Clausing: 1300 series, Monarch: 13, Nardini: MS1400 MS1600 Acer: 1340 and many other import lathes. Whole set includes one each […]

Post Tagged with , , , , , , , , ,
Read More

Genuine Kdk Quick-change Parting Bar Combination Tool Holder Kdk-204

(Jack) Kuhn of South Gate, California. This is a used Quick-Change Parting Bar Combination Tool Holder in GREAT condition. For lathes with 18″ to 24″ swing. Only a second to change tools. Rugged – No chatter or vibration. No time wasted with shims. Safe and simple to operate. Speed your lathe operations up to 90%. […]

Read More

HARDINGE QUICK CHANGE TOOL HOLDER L18 With BORING BAR AND TOOL HOLDER L21 L23

WORKS AS IT SHOULD.

Post Tagged with , , , , ,
Read More

4 Hardinge Metal Lathe Quick Change Tool Holders Boring Bar And Bit Holder

USED, HARDINGE TOOL HOLDERS. THERE ARE 3, L-21 HOLDERS AND A BORING TOOL HOLDER. THE BORING TOOL HOLDER HAS SOME RUST PITTING ON IT. LOOK AT THE PICTURES. THE LISTING IS FOR ALL 4 PIECES. CHECK OUT MY OTHER LISTINGS. NO WARRANTIES GIVEN OR IMPLIED. International Buyers – Please Note. I do not mark merchandise […]

Post Tagged with , , , , , , , ,
Read More

6PCS Piston Quick Change Tool Post Holder Set For Lathe 6 12 AXA 250-100

No time wasted with shims. All working parts hardened and precision ground. Wedge type tool post are precision engineered to assure repeatability accuracy. Wedge type tool post Have the Maximum rigidity to get the chatter free performance. Suitable for lathe center height 0.6 – 1.75″ (top compound surface to lathe center line), such as: South […]

Post Tagged with , , , , , , , ,
Read More

Enco Model E3 Quick Change Tool Holder Turret With E-3g Holder For Metal Lathe

USED, ENCO MODEL E3 TURRET. IT COMES WITH ONE HOLDER. THERE ARE MEASUREMENTS IN THE PICTURES. THE BLOCK LOCKS DOWN LIKE IT SHOULD. THERE ARE SCUFFS AND SCRATCHES FROM USE. LOOK AT THE PICTURES. CHECK OUT MY OTHER LISTINGS. NO WARRANTIES GIVEN OR IMPLIED. International Buyers – Please Note. I do not mark merchandise values […]

Post Tagged with , , , , , , , , ,
Read More

6Pcs AXA 250-111 Wedge Type Quick Change Tool Post Holder Set For Lathe 6- 12

No time wasted with shims. All working parts hardened and precision ground. Wedge type tool post are precision engineered to assure repeatability accuracy. Wedge type tool post Have the Maximum rigidity to get the chatter free performance. Suitable for lathe center height 0.6 – 1.75″ (top compound surface to lathe center line), such as: South […]

Post Tagged with , , , , , , , , ,
Read More

DTM H100-16A (CA) Quick Change Combination, Turning & Facing Tool Holder

I suspect one side was used for one small job and never used again.

Read More

3900-5424 KDK-0 Type Quick Change Tool Post and 6 Piece Holder Set

8 x 5 x 8 inches; 9.23 Pounds. Interchangeable with kdk-0,100, 150 & 200 tool posts. “Lathe swing: 8-12″ lock down bolt diameter: 7/16. 1 – turning & facing, no. 2 – threading & facing, no. 3 – extension turning bar, no. 4 – parting bar, no. 5 – master bar for boring bars. T-slot […]

Post Tagged with , , , , , , , ,
Read More

Swiftray Theme Powered by WordPress